Front Suspension
 | Inner and outer wheel bearings and seals
 |
| Brake Rotors and pads |
| Polyurethane swaybar bushing set with new metal mount straps
|
| Swaybar locator set |
| Full Polyurethane Bushing Set, A-arm lower
inner and upper outer, both sides |
| outer tie-rod ends |
| steering rack rubber gaiter boots with metal clamps x2 |
| upper shock bump stop rubbers x2 |
| Brake calipers stripped cleaned and painted gold (500°C
engine paint) |
| Entire structural suspension stripped out, cleaned,
de-rusted, and repainted |
Rear
Suspension
| Full Polyurethane Bushing Set (spring pads,
eyelets, and shackle pairs) |
| Rear brake drums de-rusted and repainted |
| Both leaf springs replaced |
| Break shoes |
| Cleaned and re-greased park brake cable and rear pivot
assembly. |
| Brake drum inspection plugs |
Interior
| Wire wheeled all metal rust, minor
fiberglass repairs, primered and repainted entire interior ** |
| ** Repeat of above in the trunk and in the
engine compartment. |
| Stripped and cleaned all of the gauges
(yes...even the press/temp gauge.) |
| Repaired inoperative odometer (replaced push bar, clip, and
installed new puller spring) |
| Striped and cleaned all the switch contacts
on the steering column |
| Stripped out, cleaned and re-installed all carpeting and
upholstery |
| Repaired all vinyl panels (filled in holes) and prep'ed new
screw mount holes properly |
| Stripped, cleaned the belts, and rebuilt the seat belt
winder mechanisims |
| Custom in-harness alarm wire routing |
| Added speaker wires to rear wiring harness and re-wrapped
|
| Repaired P.O. wiring harness abuse under the
dash and rewrapped |
| Interior Courtesy Light |
| Added two additional footwell lights |
| Window crank handles x 2 |
| Window crank handle escutcheon plates x 2 |
| Striped, cleaned, painted, rebuilt and polished inner door
latch handles and backplates x 2 |
| Door pull handles x 2 |
| Door check straps x2 |
| Furflex main door seals x 2 |
| MG Logo Rubber floor mats x 2 |
| Steering Column center shaft upper bushing
assembly rebuilt |
| Chrome like polish job of the spokes of the
steering wheel. |
| OEM style ignition key switch and column
lock (NOS) |
| New passenger seat foams, base and back |
| Seat bottom webbing, both seats |
| Seat bottom webbing canvas material both
seats |
| Completed passenger seat upholstery |
| Passenger seat recliner handle (NOS) |
| Heater fan control switch (NOS) |
| Dash switch lamp holder/mount clips x 2 |
Engine Compartment
| Professionally rebuilt
AUD136 HS2 carburators |
| Professionally rebuilt (by Ted Schumacher)
ribcase transmission |
| Borg and Beck ( a real one!) Clutch, pressure
plate, throwout bearing |
| Clutch slave cylinder |
| Heat shield sanded and painted |
| Intake
manifold polished |
| Exhaust manifold sanded and painted |
| Captive washer manifold nuts |
| Pertronix Electronic Ignition Module |
| Lucas Gold Sports Coil - 40,000
volt |
| Stainless steel exhaust front pipe |
| Monza twin tip resonator and muffler (one
piece) |
| Fuse Block stripped and rebuilt |
| Engine Bay surface cleanup and re-paint |
| Evap. Canister to Float bowl vent hoses |
| Evap. Canister to Gas Tank vent hose |
| Front Bonnet Buffer (bumpers) x2 |
| Wiring Harness cleaned up and
re-wrapped |
| Front motor mounts replaced |
| Rear transmission mounts replaced |
| Valve clearances adjusted (floated
wear) |
| Polished Aluminum Valve Cover |
| O.E.M. style PCV valve properly installed |
| Cylinder head ports and valves cleaned and de-carbonized
|
| Cylinder head combustion chambers and piston tops
decarbonized |
| Bonnet release cable (T handle..it's easier to pull)
|
| head studs |
| High performance copper head gasket |
| All radiator hoses replaced |
| Polished
carbs after rebuild |
Body and exterior
| Vent Window Seals both doors |
| Vent window assemblies to door top seals |
| Door window outer waist seals, both
doors
|
| Door window inner fuzzy seals, both doors |
| Door window channel felt liners x 4 |
| Main windshield to windshield frame seal |
| Windshield frame to body seal |
| Windshield frame posts to body seals x2 |
| Newer (good chrome condition) front
bumper |
| Newer (good chrome condition) rear
bumpers ands all mount hardware |
| Rear bumper mount hardware stripped, sanded and repainted
|
| Front bumper mount hardware stripped sanded and repainted.
|
| Headlight fixture to body gaskets, both
lamps x2 |
| Back Up Lamp lenses seals x2 |
| Back Up Lamp fixture to body gaskets x2 |
| Side Marker light assemblies x 4 lights |
| Tail Light Assemblies (whole chrome base) x2 |
| Tail Light Lens Seals x2 |
| Tail Light fixture to body gaskets |
| Windshield wiper arm gearbox bezels and
mount seals x3 |
| touch up pain (small dings here and there
...) |
| Front Wheel Arch cleanup, undercoating
and re-painted |
| Rear Wheel Arch cleanup, undercoating and re-painted |
|
